新闻资讯
吹瓶机操作和保养方法
发布日期:2017-10-19

  吹瓶机操作和保养方法
  1)预热 将瓶坯(胚)通过红外线高温灯管照射,将瓶坯(胚)的坯(胚)体部分加热软化,为了保持瓶口形状,瓶坯(胚)口是不需要加热的,因此需要一定的冷却装置对其进行冷却操作。 (2)吹瓶成型 该阶段是将已经预热好的瓶坯(胚)放置到已经做好的吹模中,对其内进行高压充气,把瓶坯(胚)吹拉成所需的瓶子。 市面上的吹瓶机一般分为全自动和半自动两种。 全自动吹瓶机通过机械手的操作将吹瓶的两个操作合在一起完成,免去了中间人工将预热好的瓶坯(胚)放入吹模的过程。大大加快了生产的速率,当然价格也为比半自动的要高。 四、操作规范 (1) 每班开机之前,必须在各活动部件加润滑油一次。(机械手、机械手导轨、开合模导轨 ) (2) 摆臂可(3-4)天加一次。加温机大链条小链条可一个月一次。经常检查主机减速器、加温机减速器是否缺油。主机轴承可3个月加一次。 (3) 生产前检查各运动部件是否牢固,螺丝是否松动脱落,特别是冲击力较强的地方,皮带传动部分是否异常。 (4) 检查高压气源,低压气源,电源,水源是否正常。 (5) 检查各急停开关,安全门开关,保护装置检测开关是否正常。 (6) 检查加温头进胚,掉胚部分工作是否正常。插胚如不到位可调节压胚装置螺母。 (7) 检查灯管是否损坏,断裂。要及时更换。 (8) 检查各气动元件是否漏气,动作是否灵敏。 (9) 检查三联体是否异常漏气,是否堵塞,水杯储水量是否太满。 (10) 全自动吹瓶机电磁阀遇有异常时,要及时清洗〈每吹瓶350万清洗一次〉
  Operation and maintenance of bottle blowing machine
  1) preheating the bottle preform (germ) by infrared heat lamp irradiation, the bottle preform billet (germ) part of (germ) heating softening, in order to keep the bottle shape and preform (germ) mouth is don't need to be heated, so you need a cooling device for cooling operations. (2) blow the bottle to form this stage is to put the preheated flask (embryo) into the blown mould already prepared, then inflate the inside of it and blow the billet (embryo) into the desired bottle. The bottle machine on the market is generally divided into automatic and semi-automatic. Fully automatic bottle blowing machine can be used to combine the two operation of the bottle with the operation of the manipulator, which will eliminate the process of putting the preheated flask (embryo) into the blowing mould. The rate of production has been speeded up, and of course prices are higher than semi-automatic. 4. Operation specifications (1) must be lubricated once before each shift is turned on. (manipulator, manipulator guide, open die guide) (2) swing arm can (3-4) day add once. A small chain can be used once a month. Check the main engine reducer and the engine reducer without oil. Main engine bearing can be added up to 3 months. (3) check whether the moving parts are strong before production, and whether the screws are loose and loose, especially where the impact force is stronger, whether the belt transmission part is abnormal. (4) check the high pressure gas source, low pressure air source, power supply and water supply. (5) check the emergency stop switch, the safety door switch, and the protection device to detect whether the switch is normal. (6) check the heating head into the embryo and remove the embryo part. The insert is not in place to adjust the nut. (7) check whether the lamp tube is damaged or broken. Change it in time. (8) check whether the pneumatic components are leaking and whether the action is sensitive. (9) check whether the triplets are abnormal, whether it is blocked, and whether the water cup is too full. (10) when there is an abnormality in the automatic blow-bottle electromechanical magnetic valve, clean the > in a timely manner
  以上内容由西安市铭德塑料包装机械无锡体彩网整理提供。铭德机械专业生产制造吹瓶机,高速吹瓶机,自动吹瓶机,全自动吹瓶机,热罐装吹瓶机,半自动吹瓶机,pet吹瓶机,塑料吹瓶机,吹瓶设备,吹瓶机厂,中空吹塑机,注塑机,瓶坯模具,瓶盖模具及配套设备,吹瓶机厂家,直销吹瓶机价格优惠,保障品质.咨询电话:13022665258 ;联系人:郭总

  • 技术支持:台州网络公司
ONLINE SERVICES
在线客服
陕西福彩网 无锡体彩网 陕西福彩网 北京福彩网 无锡体彩网 中国竞彩网 陕西福彩网 北京福彩网 北京福彩网 陕西福彩网